LAUNCH EasyDiag Unlocking Locked Adapters

good news for owners of Locked adapters LAUNCH EasyDiag dug 

around on the Internet, collected information and ... it turned out! 

I will describe the recovery steps for both Locked and Blown 

LAUNCH EasyDiag adapters . 

We need a 

dump of a non-blocked adapter (with 52 firmware on board). The programer 
itself 

runs the programmer in the J- 

and the program in which I did everything



Programs recommended by Adminom 
program for firmware adapter 



native application ST-Link


Before we begin, we will 

use the utility from Segger to turn our St-Link V2 (clone) into the J-Link programmer
and install the program (downloaded from the above) with which we will flash our Device * We disassemble the adapter (I took it apart on the board with a knife by cutting the place of the gluing of the case) 



connect the programmer to the pictures


J-Link (ST-Link V2 Clone)



launch the J-Flash application 
Create a new project select the controller STM32F207 IG 





after all the procedures connect our adapter to the computer and connect it to the program in the Target tab, select Connect 
and well on the video)) 
Good luck, the guys write, I will definitely prompt))

Programs recommended by Admin 
program for firmware adapter 
native application ST-Link

Dumps 

- firmware 11.53, boot 1.23.001 program_memory_11.53.7z (172 KB)


and up to a heap flash from non-flicked MDiag: 
- firmware 11.55, boot 1.03.000 program_memory_11.55.7z (158 KB)
- firmware 11.49, boot 1.03.000 program_memory_11.49.7z (153 KB)
- firmware 11.12, but 1.03.000 program_memory_11.12.7z (143 KB)

OTP partition from the MDiag: 
otp_memory.7z (756 Bytes)

all download in

Attached Files

LAUNCH EasyDiag Unlocking .zip
File Type
Hits	22
Size	331.15 KB

Bosch ESI 2017/1 A1 A2 B1 B2 B3

Rep +Thanks - Pass

Attached Files

Bosch ESI 20171 A1 A2 B1 B2 B3.txt
File Type
Hits	14
Size	26 bytes

Scania XCOM 2.27.1.2 + crack

Scania XCOM - is a diagnostic tool to read, save and modify ECU data such as trouble codes, parameters, statistic data etc. VCI2/VCI3 interface is used to connect to ECU via CAN protocol.


Supported modification of ECU data of the following types:

- EMS - Engine management system.
- GMS - Gearbox management system.
- RET - Retarder system.
- AWD - All wheel drive system.
- CLS - Clutch Control.
- EEC - Exhaust Emission Control.
- COO (COO7) - Coordinator.
- BWS (BCI1) - Bodywork system.

Supported resolving trouble codes to text description for the following types:

- EMS (S6, S7, S8).
- GMS (OPC4, OPC5).
- RET (RET1, RET2).
- AWD (AWD1).
- EEC (SCR1, EEC3).
- COO (COO6, COO7).
- HMS (HMS1).

Some interesting options:

- AdBlue ON/OFF.
- EGR ON/OFF.
- Chassis ID/VIN Change.
- Immobilizer ON/OFF.
- Truck Power INCREASE.
- ECU Recovery.
- ECU Reset.
- ECU Unlock without PIN.

Supported languages: English.

Attached Files

Scania XCom 2.27.2.1.zip
File Type
Hits	33
Size	34.43 KB

Jeti SH 4.34

Rep + Thanks = s

doosan epc 2017
no medicine needed

Thank + Rep - Pass

Attached Files

doosan epc 2017.zip
File Type
Hits	18
Size	220 bytes

Nets 5.5.1

Write  the serial number here
I activate

Attached Files

Nets 5.5.1.txt
File Type
Hits	4
Size	86 bytes

CarProg vCarProg v8.21 work online free!!

Rep +Thanks = Link

ODIS-E 7.2.2 ( Engineering)

Write your HW ID

Such as：
Name: ASF 
HWID :56531-29A80-D79CD-17922

I iactivate

Attached Files

ODIS-E 7.22.txt
File Type
Hits	9
Size	86 bytes